Sh*t!! Base Gasket is leaking ? WTF?

Post by **Mr. Wibbens** » 08:38 pm Apr 06 2010

I used plenty of sealer ??

This really pisses me off

Post by **Julien D** » 08:41 pm Apr 06 2010

LMAO! WTF IS THAT????

Post by **Mr. Wibbens** » 08:45 pm Apr 06 2010

**** I followed directions and everthing!

Used the whole tube!

Colorado Mike · Post by **Colorado Mike** » 11:42 pm Apr 06 2010

You used the wrong color. The yammie con rods need blue or black grilla snot, not silver.

frankenschwinn · Post by **frankenschwinn** » 10:02 am Apr 07 2010

Real question is why is there a yamaha Con. Rod in your KDX? :)

jrnolan · Post by **jrnolan** » 10:25 am Apr 07 2010

You can reuse that.

Post by **Mr. Wibbens** » 12:33 pm Apr 07 2010

frankenschwinn wrote:Real question is why is there a yamaha Con. Rod in your KDX? :)

Maybe thats why it runs so strong?

KDXsg · Post by **KDXsg** » 07:48 pm Apr 07 2010

why is there a need to use sealer when there is the gasket for it. nobody uses sealer on the top end. just the base gasket will do. and looking at the cond rod and the condition around the crank, think the bike is poorly maintain.

91kdx200 · Post by **91kdx200** » 08:17 pm Apr 07 2010

Thats why you have to use JB Weld instead. Guaranteed not to leak as long as you use the whole tube.

Post by **Mr. Wibbens** » 08:40 pm Apr 07 2010

KDXsg wrote:why is there a need to use sealer when there is the gasket for it. nobody uses sealer on the top end. just the base gasket will do. and looking at the cond rod and the condition around the crank, think the bike is poorly maintain.

Cuz I dint have a gasket dummazz

Geez are yuse stoopid or sumpthin?????

Jupiter2 · Post by **Jupiter2** » 08:53 pm Apr 07 2010

Just squeeze on another tube. You'll be fine~

Post by **Indawoods** » 08:54 pm Apr 07 2010

Have you tried really big hose clamps?

Post by **Mr. Wibbens** » 08:56 pm Apr 07 2010

I did

I had some of this from another project, but I think it'll be ok

KDXsg · Post by **KDXsg** » 11:03 pm Apr 07 2010

pot calling the kettle black. mr wibben, human being make gasket for a reason, if you think everything can be solved with sealant....a bit of common sense will tell NO! put that ego of yours down abit and admit that its a mistake of you to have use sealant for something as simple as that. There is no need to be rude and call me stupid when i think that applys to you too., if I am one...haha..have a good time then messing around that junk....

Post by **Indawoods** » 11:05 pm Apr 07 2010

The entire post was tongue in cheek KDXsg... relax.....

Post by **Mr. Wibbens** » 11:16 pm Apr 07 2010

How'd you guess ?

Post by **scheckaet** » 12:28 am Apr 08 2010

read the green warning disclaimer at the bottom of wibb's profile

KarlP · Post by **KarlP** » 06:22 am Apr 08 2010

That liquid nails stuff is the bomb.

It'll work better than than silver stuff.

However, if the problem is a water leak your bestest bet would be to cut your own gasket out of roofing felt and use tar on both sides.

IMO

Jupiter2 · Post by **Jupiter2** » 07:21 am Apr 08 2010

I have my own special recipe. Never had a leaked yet!
[img][img]http://i802.photobucket.com/albums/yy30 ... tarpit.jpg[/img][/img]

Post by **Julien D** » 07:32 am Apr 08 2010

Indawoods wrote: The entire post was tongue in cheek KDXsg... relax.....

You should have let him carry on, this was just getting entertaining!

KDXRIDER.NET

KDXRIDER.NET

Sh*t!! Base Gasket is leaking ? WTF?

Sh*t!! Base Gasket is leaking ? WTF?