Knobby cutting
- bradf
- Gold Member
- Posts: 703
- Joined: 02:17 am Dec 11 2004
- Country: USA
- Location: Anderson, SC
- canyncarvr
- Gold Member
- Posts: 6943
- Joined: 01:07 pm Nov 05 2004
- Country: US
- Location: The Mythical State of Jefferson
An undercut lug is going to have the same problem as a tractor tire put on backwards.
Looking at a tractor (or grader or earthmover or your choice) tire you may think, 'It would grab a whole lot better if it went the other way!'
Yep. It will grab until it packs..then the grabbing is over.
It's Maxxis Razors I think you put on 'either' way depending on the terrain. One way for sand (no packing there) the opposite for mud ('self cleaning' is the term).
Looking at a tractor (or grader or earthmover or your choice) tire you may think, 'It would grab a whole lot better if it went the other way!'
Yep. It will grab until it packs..then the grabbing is over.
It's Maxxis Razors I think you put on 'either' way depending on the terrain. One way for sand (no packing there) the opposite for mud ('self cleaning' is the term).
Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis
bike profile: !clicky!
- KanuckKDX
- Member
- Posts: 166
- Joined: 08:35 pm May 28 2005
- Country:
- Location: Alberta Canada eh
>|QBB<[/url]
I would be pleased if my tire had edge like that even if it chunked off a piece.Mr. Wibbens wrote:Most of the time or at least a lot, I replace my tires not because th knobs are wore down but because the rubber is just too wore out and the carcus is too soft
Got a flat on the DR this summer, and you could stick your finger all the way through the hole, the rubber was soft as butter
My next tire chunked at 189 miles
KanuckKDX
'01 YZ426F son's
'02 XR400 still for sale
'04 KTM 450exc it's all about the e-start
'01 YZ426F son's
'02 XR400 still for sale
'04 KTM 450exc it's all about the e-start
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
That tire had about 3 rides on it
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- skipro3
- Gold Member
- Posts: 4329
- Joined: 11:58 pm Nov 04 2004
- Country:
- Location: BANNED FOR LIFE!!
- Contact:
Hey carvr; the tire, undercut or not, would not pack up if you could spin the rear tire and clear it. My KX did it in spades. My KDX would if I just leaned the girl over a little. A spinning knobby will throw the mud off it.
I recall feeling my knobby load up when we rode GT on day two over on Darling Ridge. That was after the deep water crossing and up the gravel road. The loggers took out our trail and left a fine mess. You remember, right? Sure..... That's where you fell!!! Haw! I remember that!! So cool to watch the great Carvr lay that bike right over on it's side. HaWWWW!! SnorT!!
Ya know....
For just a minute there, you; me; and m0rie were sitting in a saloon watching a pretty girl pick a tune out on the juke box while swapping storys and lies about the day's ride.
(Damn)
Cheers fellas!!
I recall feeling my knobby load up when we rode GT on day two over on Darling Ridge. That was after the deep water crossing and up the gravel road. The loggers took out our trail and left a fine mess. You remember, right? Sure..... That's where you fell!!! Haw! I remember that!! So cool to watch the great Carvr lay that bike right over on it's side. HaWWWW!! SnorT!!
Ya know....
For just a minute there, you; me; and m0rie were sitting in a saloon watching a pretty girl pick a tune out on the juke box while swapping storys and lies about the day's ride.
(Damn)
Cheers fellas!!
Jerry
I'd rather be a smartass like carvr, than a dumbass like.... well, you fill in the blank!
I'd rather be a smartass like carvr, than a dumbass like.... well, you fill in the blank!
- Jeb
- Gold Member
- Posts: 1894
- Joined: 08:01 pm Jul 14 2006
- Country:
- Location: Cincinnati / Northern Kentucky
- bradf
- Gold Member
- Posts: 703
- Joined: 02:17 am Dec 11 2004
- Country: USA
- Location: Anderson, SC
That exceedingly intelligent and respectful individual knows how to cut tires! He is my hero! Risking it all on a paved street with an un-licensed bike shows his conscious was thinking about the public good instead of his own while he probably wiped pornographic graffiti off the surface so our children wouldn't have to see it. He was brought up to work hard for every penny mowing lawns and doing manual labor but his hard work with lower than average wages meant nothing as he scrapes up his last penny to buy a new rear tire so he can erase some more naughty words from US-441. We need more like him. I wish I was.
'04 220 w/'01 KX250 USD forks, '02 RM125 Showa shock, Rekluse EXP 3.0, LHRB & all RB'd
- KanuckKDX
- Member
- Posts: 166
- Joined: 08:35 pm May 28 2005
- Country:
- Location: Alberta Canada eh
Re: Knobby cutting
I just re-read this opening to this thread. I didn't notice this crude insult at first but now that I have thought about it I have decided to be offended. Saving money doesn't make me the "cheap bastage" I thought I was at first. And what is a bastage?bradf wrote:Do any of you cheap bastages sharpen your knobbys like I do?
KanuckKDX
'01 YZ426F son's
'02 XR400 still for sale
'04 KTM 450exc it's all about the e-start
'01 YZ426F son's
'02 XR400 still for sale
'04 KTM 450exc it's all about the e-start
- 80elkster
- Supporting Member II
- Posts: 135
- Joined: 08:43 pm Jan 01 2006
- Country:
- Location: Maple Valley WA
I use an angle head grinder, takes about 10 - 15 minutes. I put the bike on a stand or crate keeping the tire off the ground and so that I can rotate it. It does create some smoke and thows little molten blobs of rubber so I set up a fan to blow the smoke outside and sweep up the rubber when i'm done. I've heard of other folks putting a cutting wheel on their grinder to do this. I didn't have one so I tried the standard grinding wheel. Worked good for me!
06 DR650 Farkled
91 WR250 2T
00 300EXC (Sold)
79 XS850 (Sold)
79 CR250 (Sold)
78 IT400 (Stolen)
75 G5 100 Kawi (Gave it away)
73 F7 175 Kawi (Sold)
70 175 Brigestone (Recycled)
05 KDX200(Son's)
93 KDX200
75 KT250 Trials
250 Quads
Just glad to be ridin!
91 WR250 2T
00 300EXC (Sold)
79 XS850 (Sold)
79 CR250 (Sold)
78 IT400 (Stolen)
75 G5 100 Kawi (Gave it away)
73 F7 175 Kawi (Sold)
70 175 Brigestone (Recycled)
05 KDX200(Son's)
93 KDX200
75 KT250 Trials
250 Quads
Just glad to be ridin!