Jet Block Gasket.
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
Should I just install the jet block gasket as it came out of the package? Or, is there a better way to re-assemble my carb. Looks like my gasket was ok, bike runs fine. I'm replacing it because it's 15 years old. Well, I just wanted to. I've never changed one before. Thanks in advance. JB
If you lend someone $20, and never see that person again, it was probably worth it.
- bufftester
- Platinum Member
- Posts: 3462
- Joined: 06:03 pm Oct 31 2012
- Country: USA
- Location: University Place, WA
Re: Jet Block Gasket.
Just as it came. It can be a bit tricky to get it on there and the block back on, I used a tiny dab of vaseline to help hold it in place. That's how I ended up doing my KLX300 engine rebuild, just because I wanted to and had never done a 4T lol
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
Thanks, I wondered about a dab of grease or something similar. Thanks!!!
If you lend someone $20, and never see that person again, it was probably worth it.
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
Ok, What's a 4T?
If you lend someone $20, and never see that person again, it was probably worth it.
- KDXGarage
- KDXRider.net
- Posts: 14082
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Jet Block Gasket.
It's an engine style when simplicity and lack of parts just won't do.
I am just kidding. They are quite nice. My push lawn mower has one. I assume a motorcycle with one would be very similar, when anything goes wrong, just go buy a new one.
I am just kidding. They are quite nice. My push lawn mower has one. I assume a motorcycle with one would be very similar, when anything goes wrong, just go buy a new one.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
If it doesn't fit, force it. If it breaks, it needed to be replaced anyway.
Oh, I was just kidding.
Oh, I was just kidding.
If you lend someone $20, and never see that person again, it was probably worth it.
- bufftester
- Platinum Member
- Posts: 3462
- Joined: 06:03 pm Oct 31 2012
- Country: USA
- Location: University Place, WA
Re: Jet Block Gasket.
How painfully close to the truth that cutsJason wrote:It's an engine style when simplicity and lack of parts just won't do.
I am just kidding. They are quite nice. My push lawn mower has one. I assume a motorcycle with one would be very similar, when anything goes wrong, just go buy a new one.
-
- Supporting Member II
- Posts: 58
- Joined: 04:28 pm May 25 2015
- Country:
Re: Jet Block Gasket.
I've never understand why 4T and 2T uses a T? If we say 4 stroke why not 4S?
1982 Kawasaki KZ1300
1999 Kawasaki KDX220
2003 Kawasaki KLX400SR
1999 Kawasaki KDX220
2003 Kawasaki KLX400SR
-
- Member
- Posts: 27
- Joined: 10:07 am Apr 15 2014
- Country:
Re: Jet Block Gasket.
My original gasket had sealant, I used Permatex High Tack Gasket Sealant.
Some install without anything.
Must be ok either way as I don't hear of failures after installation.
Some install without anything.
Must be ok either way as I don't hear of failures after installation.
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
I just rubbed some 2 stroke oil on the gasket & put it right together. All seemed well.
If you lend someone $20, and never see that person again, it was probably worth it.
- bufftester
- Platinum Member
- Posts: 3462
- Joined: 06:03 pm Oct 31 2012
- Country: USA
- Location: University Place, WA
Re: Jet Block Gasket.
The T is from German: coming from "Takt" meaning stroke, or cycle.raygun wrote:I've never understand why 4T and 2T uses a T? If we say 4 stroke why not 4S?
- B737driver
- Gold Member
- Posts: 491
- Joined: 01:11 pm Dec 02 2011
- Country:
- Location: Heath, Texas
Re: Jet Block Gasket.
Danke schoen...I’ve often wondered the same.bufftester wrote:The T is from German: coming from "Takt" meaning stroke, or cycle.raygun wrote:I've never understand why 4T and 2T uses a T? If we say 4 stroke why not 4S?
Live to Fly
Fly to Live
Fly to Live
-
- Supporting Member I
- Posts: 172
- Joined: 09:07 pm Feb 08 2017
- Country: USA
- Location: Sykesville, MD
Re: Jet Block Gasket.
I am not sure where this 'jet block gasket' sits in the carb. Does anyone have a photo?
I just bought the "All Balls" carb rebuild kit for my '97 KDX 220 from MOTOSPORT and I don't think it came with this 'jet block gasket'.
Should I have any other worries with this carb kit? The needle that came with it is silver colored, and not brass looking. Should I keep factory needle? In forum searches I have seen mentioned that the factory needle is no good, but I don't know that the needle in this kit would be any better (or worse).
I just bought the "All Balls" carb rebuild kit for my '97 KDX 220 from MOTOSPORT and I don't think it came with this 'jet block gasket'.
Should I have any other worries with this carb kit? The needle that came with it is silver colored, and not brass looking. Should I keep factory needle? In forum searches I have seen mentioned that the factory needle is no good, but I don't know that the needle in this kit would be any better (or worse).
-
- Gold Member
- Posts: 878
- Joined: 06:59 am Jan 27 2017
- Country: US
- Location: Florida
Re: Jet Block Gasket.
Google "PWK jet block gasket" and click images. It doesn't come in rebuild kits. Jets R Us has them.
If you use the all balls needle start rich like in clip 4 and lean it from there. Who knows how close their tolerances are and we're talking hundredths or thousanths of an inch making a difference in the way the bike runs. I would rather have a genuine Keihin needle like the CEL which is a known good needle for many KDX'ers. If not the CEL, then I would run the stock one.
If you use the all balls needle start rich like in clip 4 and lean it from there. Who knows how close their tolerances are and we're talking hundredths or thousanths of an inch making a difference in the way the bike runs. I would rather have a genuine Keihin needle like the CEL which is a known good needle for many KDX'ers. If not the CEL, then I would run the stock one.
- Molly's 70
- Platinum Member
- Posts: 568
- Joined: 04:29 pm Jun 18 2017
- Country: USA
- Location: Wichita, Kansas USA
Jet Block Gasket.
Like posted earlier, Get the jet block gasket from "jets r us" You have to use a torx bit to get to it. (Torx security 20)? I think.
If you lend someone $20, and never see that person again, it was probably worth it.
- SS109
- KDXRider.net
- Posts: 5799
- Joined: 05:11 am Aug 23 2009
- Country: USA
- Location: Tucson, AZ, USA
- Contact:
Jet Block Gasket.
Jet block gasket for the PWK: http://www.jetsrus.com/individual_parts/021_532_su.html
Youtube Channel: WildAzzRacing
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R
-
- Supporting Member I
- Posts: 172
- Joined: 09:07 pm Feb 08 2017
- Country: USA
- Location: Sykesville, MD
Re: Jet Block Gasket.
Parts on the way! Bought special torx security bits to open it up. Thanks!SS109 wrote:Jet block gasket for the PWK: http://www.jetsrus.com/individual_parts/021_532_su.html
Sent from my SM-G900V using Tapatalk
- SS109
- KDXRider.net
- Posts: 5799
- Joined: 05:11 am Aug 23 2009
- Country: USA
- Location: Tucson, AZ, USA
- Contact:
Jet Block Gasket.
Awesome! I hope it that is the final piece you need to get your KDX running great!
Youtube Channel: WildAzzRacing
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R