Hello All!
I've been on the streets for the past few years, owning half a dozen street bikes or so. The other day my brother expressed interest in getting rid of the old beater KDX. I remember bombing around on it many years ago when my feet couldn't touch the ground and I could barely kick start it on my own.
Anyways, fast forward to a few weeks ago when I acquired the bike from my brother. Just brings a smile seeing an old friend. That smile soon faded and I went to ripping the bike apart that had not been cleaned in every bit of 10 or 15 years.
Kicking it over seemed to have okay compression, but not great. So I pulled the motor out and have been cleaning and disassembling as I go. The whole KIPS system is trash. Gears are shredded, shafts are broken, and now I see why my brother kept saying 'it just doesn't have the power I think it should.' It was also in need of a top end overhaul for far too long.
I hope to learn a lot from you guys! I'm a forum junky who frequents WristTwisters and CBRXX. Hopefully I can find the KIPS stuff for relatively cheap and have this bike going back together sooner than later.
Good ol' 1993 KDX200
- kx200
- Supporting Member I
- Posts: 242
- Joined: 08:30 pm Dec 02 2013
- Country:
- Location: Iowa
Good ol' 1993 KDX200
good luck on getting parts for the E series they are getting very hard to find
- Gotanubike
- Supporting Member III
- Posts: 898
- Joined: 01:00 pm May 22 2013
- Country:
- Location: Ontario, Can
Good ol' 1993 KDX200
Have a look here---> link for durable steel KIPS replacements for 89-94 E series
1990 KDX200
Bike Profile -> http://www.kdxrider.net/forums/viewtopi ... 61#p136315
Suspension Overhaul(Shock+89-92 conventional forks) -> http://www.kdxrider.net/forums/viewtopi ... 15&t=15255
96'-98' RM125 Showa 49mm fork swap -> http://www.kdxrider.net/forums/viewtopi ... 04&t=16994
KDXrider world map! -> https://www.zeemaps.com/map?group=186158
Bike Profile -> http://www.kdxrider.net/forums/viewtopi ... 61#p136315
Suspension Overhaul(Shock+89-92 conventional forks) -> http://www.kdxrider.net/forums/viewtopi ... 15&t=15255
96'-98' RM125 Showa 49mm fork swap -> http://www.kdxrider.net/forums/viewtopi ... 04&t=16994
KDXrider world map! -> https://www.zeemaps.com/map?group=186158
- KDXGarage
- KDXRider.net
- Posts: 14059
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Good ol' 1993 KDX200
Welcome to the forums. Good luck on the rebuild.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
-
- Member
- Posts: 4
- Joined: 09:48 pm Jul 21 2015
- Country:
Good ol' 1993 KDX200
Thanks for the warm welcome and the link to some steel KIPS valves! I like this place already!!
Here is what I'm starting off with... Not much but here she is-
Here are a few of the chunks that used to be a power valve-
And having a shop full of goodies always helps! After letting the jug soak overnight in carb cleaner, I rinsed it off, dried it, then lined the barrel with masking tape, ripped off a piece of cardboard that used to hold a 12-pack, rolled the cardboard into the barrel to hold the tape in place, and sandblasted the whole thing. Looks much better than she did!
I'll get a build thread going here soon. I usually wait until it's done and make a long thread/post. Stay tuned
Here is what I'm starting off with... Not much but here she is-
Here are a few of the chunks that used to be a power valve-
And having a shop full of goodies always helps! After letting the jug soak overnight in carb cleaner, I rinsed it off, dried it, then lined the barrel with masking tape, ripped off a piece of cardboard that used to hold a 12-pack, rolled the cardboard into the barrel to hold the tape in place, and sandblasted the whole thing. Looks much better than she did!
I'll get a build thread going here soon. I usually wait until it's done and make a long thread/post. Stay tuned