Crude 220 stock cylinder castings
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
Here's a couple pictures of my 220 cylinder I'm cleaning up before reassembling.
Notice how the stock left hand port has a casting piece that looks like it could break
off at any time.
Not saying everyone should attempt this or rush to tear their bike apart , just something
to think about next time you have the top end off.
Notice how the stock left hand port has a casting piece that looks like it could break
off at any time.
Not saying everyone should attempt this or rush to tear their bike apart , just something
to think about next time you have the top end off.
Last edited by C George on 05:02 am Mar 20 2014, edited 2 times in total.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
Then after I start this project , I read all about the negatives of porting a KDX.
Thoughts ???? Oh well , gotta finish it now.
Like I said , I have no plans of altering the exhaust port , so it shouldn't kill the wonderful 220 bottom end.
Thoughts ???? Oh well , gotta finish it now.
Like I said , I have no plans of altering the exhaust port , so it shouldn't kill the wonderful 220 bottom end.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
The final finish is alot less shiney than this picture.
A new Wiseco and Head on it's way to RB .
I'm making a 5mm / 3/16 Intake spacer as the reed cage
blocks some of the air going to the rear boost port.
Too many changes , so I'll only be able to post an overall result.
14" snow here this week , so the bike will be in the basement for a few months.
A new Wiseco and Head on it's way to RB .
I'm making a 5mm / 3/16 Intake spacer as the reed cage
blocks some of the air going to the rear boost port.
Too many changes , so I'll only be able to post an overall result.
14" snow here this week , so the bike will be in the basement for a few months.
Last edited by C George on 05:28 am Feb 08 2014, edited 1 time in total.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- ICRage42
- Supporting Member
- Posts: 598
- Joined: 07:24 am Jan 09 2013
- Country:
- Location: Kawasaki, Ninja Ohio
Crude 220 stock cylinder castings
ok ya got me what was the end result?
No offense a test is all that a test. Hopefully not catastrophic.
No offense a test is all that a test. Hopefully not catastrophic.
If you cant fix it with a hammer, you have an electrical problem.
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
ICRage42 wrote:ok ya got me what was the end result?
No offense a test is all that a test. Hopefully not catastrophic.
I don't take that as an offense at all , I like experimenting , it's just no fun to
think what it may cost to get it back to stock.
I've learned a ton in the last week and I now know why people like EG say the 220
factory porting is screwed up . Yes and No ,,, it makes GREAT low end power for
the ultimate torque , just a totally unconventional design compared to the 200.
14" fresh snow here ,,, it will be in the basement for a few more months.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
Got it out of the basement today.
Still breaking it in but so far it pulls real strong off the bottom.
RB'd head and other small mods I'm sure helped also.
Still breaking it in but so far it pulls real strong off the bottom.
RB'd head and other small mods I'm sure helped also.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
Got to ride it some more tonight. A very noticeable difference in overall power.
It's a different bike ,, It pulls so much stronger ,,, BUT you have to remember that
I did the intake porting , installed a 3/16" reed spacer, new Boyesen Carbon Fiber reeds , RB experimental
high compression head " for 96 octane min. " , New Wiseco Piston all at the same time.
It's a different bike ,, It pulls so much stronger ,,, BUT you have to remember that
I did the intake porting , installed a 3/16" reed spacer, new Boyesen Carbon Fiber reeds , RB experimental
high compression head " for 96 octane min. " , New Wiseco Piston all at the same time.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- fuzzy
- KDXRider.net
- Posts: 3437
- Joined: 01:29 pm Jun 18 2003
- Country:
- Location: Fredneck, MD
Re: Crude 220 stock cylinder castings
That head should net most of your gain.
'91 KDX 200 Project $300 KDX
'95 KDX 200 Project $600 KDX
'94 WR 250 Always a project
'95 KDX 200 Project $600 KDX
'94 WR 250 Always a project
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Crude 220 stock cylinder castings
I put the finishing touches on the engine tonight as I bumped the ign. timing to match the fuel.
Very happy with all the work and combination of mods this winter.
Smooth linier power any where you want it.
Very happy with all the work and combination of mods this winter.
Smooth linier power any where you want it.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- KDXGarage
- KDXRider.net
- Posts: 14071
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Crude 220 stock cylinder castings
Cool that it worked out so well for you.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Re: Crude 220 stock cylinder castings
I let my son ride it and now I can't get it back ,,,,Jason wrote:Cool that it worked out so well for you.
He says " This bike is soo much more fun "
Here comes a 220 conversion / modification for next winter
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Re: Crude 220 stock cylinder castings
I'd only do this again if your going to send the cylinder out afterwards for a replate.
The stock electrofusion coating is too easy to chip.
The stock electrofusion coating is too easy to chip.
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- KDXGarage
- KDXRider.net
- Posts: 14071
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Crude 220 stock cylinder castings
Thanks for the follow up.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128