KDX E3 - clutch spring release broken
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
KDX E3 - clutch spring release broken
Noticed the other day that the SPRING, CLUTCH RELEASE that goes around the clutch lever shaft was broken. It does not seem to affect engagement or disengagement of the clutch. In order to replace, I'd need to pull the clutch cover off, pull the shaft, replace the oil seal, and reassemble in reverse order. My question is this - is it absolutely necessary to replace this spring or can I go without it?
It is #92144 in the image below.
It is #92144 in the image below.
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
KDX E3 - clutch spring release broken
you may wear out the clutch plate faster if the clutch doesn't release completely...
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
Re: KDX E3 - clutch spring release broken
Last time I rode it, it didn't feel like the clutch was dragging... put the bike in neutral with the clutch lever disengaged and the bike idled fine. Same thing when I put it into gear and held the clutch in. For the sake of thoroughness, I'll replace the spring over the winter. I might have to replace the kick start spring too as it slips from time to time.
This bike is starting to turn into a money pit...
This bike is starting to turn into a money pit...
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
KDX E3 - clutch spring release broken
I think that spring is one of those parts that is nice to have but not completely necessary. If you have the cover off then it would probably be a good idea to change it but I don't think it would stop me from riding until I had the chance to fix it.
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
KDX E3 - clutch spring release broken
Thanks for the feedback.rbates9 wrote:I think that spring is one of those parts that is nice to have but not completely necessary. If you have the cover off then it would probably be a good idea to change it but I don't think it would stop me from riding until I had the chance to fix it.
I'll eventually replace it. The cost of the spring and oil seal is negligible. Just not thrilled with the actual process of taking the thing apart and putting it all back together again.
-
- Member
- Posts: 358
- Joined: 09:12 pm Nov 30 2009
- Country:
- Location: Singapore
KDX E3 - clutch spring release broken
Dont bother to even buy or replace or install a new release spring. it doesnt hinder any clutch operation.
I too run without one, cause by having the spring, it actually wears out the oil seal belows it causing some oil leak.
I too run without one, cause by having the spring, it actually wears out the oil seal belows it causing some oil leak.
A true KDX customizer!!
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
Re: KDX E3 - clutch spring release broken
Interesting. I didn't notice any oil seal wear on my bike but now that you've mentioned it, I'll take a closer look.
Still - the engineers felt it was necessary to have a return spring for some reason. I can't see running without one for an extended period of time to be a good thing on the clutch?
Still - the engineers felt it was necessary to have a return spring for some reason. I can't see running without one for an extended period of time to be a good thing on the clutch?
-
- Supporting Member
- Posts: 133
- Joined: 10:37 am Apr 11 2008
- Country:
Re: KDX E3 - clutch spring release broken
Clutch engagement /disengagement is controlled by clutch springs themselves.The spring in your description is only there to take up cable slack so the clutch lever does'nt shake around
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
Re: KDX E3 - clutch spring release broken
Ahh... ok, that makes sense. I will not replace it then. That saves me the hassle of draining the oil and tearing the thing down just to replace that spring.
OTOH, if my kick starter begins to slip even more than it does now, then I'll replace the clutch release spring when I work on the kick start assembly.
OTOH, if my kick starter begins to slip even more than it does now, then I'll replace the clutch release spring when I work on the kick start assembly.
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
KDX E3 - clutch spring release broken
That little clutch arm spring may also be there to keep the arm shaft from riding on the pusher shaft in the center of the clutch with the tiny ball bearing.
-
- Member
- Posts: 477
- Joined: 05:59 pm May 01 2011
- Country:
- Location: Calabogie ontario canada
KDX E3 - clutch spring release broken
what tiny ball bearing Bates? Is it behind the pusher shaft?
Fletch
89 kdx 200 with 99 rm125 forks
89 kdx 200 with 99 rm125 forks
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
KDX E3 - clutch spring release broken
Yup 92045 in the diagram above
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
Re: KDX E3 - clutch spring release broken
Could you please provide a link to a diagram that shows that ball bearing? I'm curious, thanks.
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
KDX E3 - clutch spring release broken
rbates9 wrote:Yup 92045 in the diagram above
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
KDX E3 - clutch spring release broken
When you pull the clutch cover off you will see the the spring (when it is there) is holding the flat spot in the shaft parallel to the pusher shaft allowing for a maximum gap. It might not mean anything but that is the best I could come up with. And it does pull the cable back a bit too.
-
- Member
- Posts: 477
- Joined: 05:59 pm May 01 2011
- Country:
- Location: Calabogie ontario canada
- amstel78
- Supporting Member
- Posts: 158
- Joined: 11:22 pm Jul 14 2012
- Country:
- Location: NEPA
- Contact:
KDX E3 - clutch spring release broken
Thanks.rbates9 wrote:Yup 92045 in the diagram above