For the record, I have my cable routed like you did behind the petcock. All that matters is proper cable operation and it will operate perfectly like that. There is zero binding that way and my boot hasn't worn through.
One thing no one has considered is manufacturing tolerances and the small amount of wiggle room in the engine mounting. It can all add up to cause the interference you're seeing and especially so adding an aftermarket parts in to the equation. I'll try to get a pic of mine tomorrow.
As for the petcock itself, I think I found a better fitting one than the one I bought and recommended. The one used on the '18 YZ250X will fit much better as it has a straight down outlet instead of the rear facing one.
Supertight squeeze for throttle cable… and slide question…
- SS109
- KDXRider.net
- Posts: 5796
- Joined: 05:11 am Aug 23 2009
- Country: USA
- Location: Tucson, AZ, USA
- Contact:
Re: Supertight squeeze for throttle cable… and slide question…
Youtube Channel: WildAzzRacing
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R
AZ State Parks & Trails OHV Ambassador - Trail Riders of Southern AZ
Current KDX: '98 KDX220
Old KDX: '90 KDX200 -White/Blue
'11 GasGas EC250R
- MoonStomper
- Gold Member
- Posts: 567
- Joined: 02:05 pm Jun 02 2020
- Country: USA
- Location: Blacksburg, Virginia
- Contact:
Re: Supertight squeeze for throttle cable… and slide question…
Thanks for the suggestion on this other petcock. I really do like my routing like it is, but that might be even stealthier yet. I see other bikes out there with fuel filters and wires and stuff hanging out around that area ready to be snagged and just wonder how they get away with it.
Here’s the stock reed boot that came off mine - it’s at least a half inch, probably closer to 3/4” narrower than the Boyesen on there now, no wonder the carb is so far back, but OH MAN SHE RIPS!
Here’s the stock reed boot that came off mine - it’s at least a half inch, probably closer to 3/4” narrower than the Boyesen on there now, no wonder the carb is so far back, but OH MAN SHE RIPS!
~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
- MoonStomper
- Gold Member
- Posts: 567
- Joined: 02:05 pm Jun 02 2020
- Country: USA
- Location: Blacksburg, Virginia
- Contact:
Re: Supertight squeeze for throttle cable… and slide question…
Slick_Nick, I appreciate your input a ton! The cable isn’t bound up, it’s operating perfectly. Initially I couldn’t understand how the top of my carb was tucked in so tight beneath the frame brace. It was going to be that way no matter which petcock I ran due to the wide Boyesen Radvalve setup Fredette upgraded me too. I didn’t realize before how much wider it was than stock. I don’t think my throttle cable was run outboard of the oem petcock when I got this bike so that has never been an issue to me. It’s set up now like I had it before. I have Shoe Goo on the throttle boot to insulate it from tearing again, I’ll keep an eye that.
Next time I visit Jeff I’ll take a close look (and pictures) of how he runs his stuff and report back.
Next time I visit Jeff I’ll take a close look (and pictures) of how he runs his stuff and report back.
~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
- KDXGarage
- KDXRider.net
- Posts: 14071
- Joined: 06:45 am Nov 01 2004
- Country: United States of America
- Location: AL, USA
- Contact:
Re: Supertight squeeze for throttle cable… and slide question…
Ask him if he will cut you a deal on his VHS cassette of setting up a 1995+ KDX. It is a great video.
Thank you for participating on kdxrider.net.
To post pictures from a device: viewtopic.php?f=88&t=24128
To post pictures from a device: viewtopic.php?f=88&t=24128
- MoonStomper
- Gold Member
- Posts: 567
- Joined: 02:05 pm Jun 02 2020
- Country: USA
- Location: Blacksburg, Virginia
- Contact:
Re: Supertight squeeze for throttle cable… and slide question…
RE: video… you are right I should! Hoping to get a in-person ice racing setup later this month for the Steel Shoe race. Hopefully things stay cold up here so there is enough ice! Just hooked up to a unit in Middlebury, Indiana and it’s 10 degrees up here, when I left Virginia this afternoon it was 58!
~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~^~
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA
Let the good times ROLL!!!!!!!!!!!!!!!!
‘99 KDX 220 / '03 KDX 200 - @%@ '18 Trek Slash 8 @%@ ‘22 Rieju MR300 Racing
BLACKSBURG, VIRGINIA USA