eats too much gas & stalls after warming up
-
- Supporting Member II
- Posts: 27
- Joined: 10:02 pm Jun 27 2015
- Country:
eats too much gas & stalls after warming up
Have a 2005 kdx200. Has #160-#48 stock jetting. I ride with all 250 motorcrossers that have 2 gallon tanks as opposed to the kdx200 with nearlly 3 gallons. When they reach around 1/2 tank i am @ less than a 1/4 with the smaller engine?? It is a real problem on longer rides (you can only carry so much extra fuel). I have checked boysen reeds, cleaned carb, checked compression, repacked silencer, all checks were good. i have a stock pipe with a pro circuit silencer. The air box is open. It stalls after getting hot when u stop. The idle screw doesnt help when it starts stalling. Tried to jet myself it seemed to crackle @ low end (1st & 2nd) ok through 3rd through 6th (followed Julians post on jetting). Its hard to tell no experience in jetting & no other kdx to compre to. Plug looks rich but shouldnt be with air box open correct? plus it's chewing gas. Finally took to the shop who said carb was filthy. My bad after cleaning carb forgot to tighten clamp o n intake boot after 1st ride. Said he did a chop test but dont believe him. plug looks rich. Going to do my own today. Have seen posts on jet body O ring. Could this be the coulprit? Where do u buy a torx security bit? The shop guy said he soaked carb overnight. i did clean & check all adjustments in carb. Now he says i may need a device for the flywheel to make it stop stalling? Gut feeling is he is on the wrong track. running 40:1. Whatta think??
- Julien D
- KDXRider.net
- Posts: 5858
- Joined: 07:53 pm Nov 07 2008
- Country: USA
- Contact:
Re: eats too much gas & stalls after warming up
I would definitely lean towards a leaking jet block gasket/oring/thingie. Pretty cheap to buy and easy to swap out. Absolutely worth a shot before you spend too much time banging your head on a wall!
- KDXohio
- Supporting Member
- Posts: 825
- Joined: 06:04 pm Jun 19 2013
- Country: United States
- Location: Dayton, Ohio
Re: eats too much gas & stalls after warming up
+1 on the jet block gasket especially knowing it was soaked. You can get the security bits at lowes kobalt has a couple nice sets or harbor freight if its something you wont use much.
1990 KDX200 FMF Fatty, Answer VFC silencer, VForce 3 Cage, Wiseco Piston, KX125-J series KYB USD fork conversion, Race tech goldvalves, J series front brake assembly, air-box snorkel removed, Acerbis Headlight, KX450F Front fender, Pro Taper RM bend bars, ASV front Brake lever, MSR Clutch perch and lever, RB Head mod, 36mm PWK carb, Trail Tech Kickstand.
-
- Supporting Member II
- Posts: 27
- Joined: 10:02 pm Jun 27 2015
- Country:
Re: eats too much gas & stalls after warming up
Thanks give it a shot. Let you know. BigH
- Julien D
- KDXRider.net
- Posts: 5858
- Joined: 07:53 pm Nov 07 2008
- Country: USA
- Contact:
Re: eats too much gas & stalls after warming up
I just used a small punch to break off the little center for the security torx, and was then able to use a regular bit to remove the jet block.
- Tedh98
- Supporting Member II
- Posts: 1576
- Joined: 01:08 pm Mar 20 2009
- Country:
- Location: Atlanta, Georgia
- Contact:
Re: eats too much gas & stalls after warming up
I never thought of that, good idea. I ground the center post out with a dremel.Julien D wrote:I just used a small punch to break off the little center for the security torx, and was then able to use a regular bit to remove the jet block.
- Jaguar
- Supporting Member
- Posts: 590
- Joined: 01:32 am Jul 03 2013
- Country: Paraguay
- Location: Paraguay
- Contact:
Re: eats too much gas & stalls after warming up
opening up the airbox makes it run leaner, but not lean enough in your case.
sounds like you need a different pilot jet also.
sounds like you need a different pilot jet also.
Performance CDI -- KDX motocross mods -- the SR KDX -- expansion chamber analysis---> http://www.dragonfly75.com/moto/
- C George
- Supporting Member II
- Posts: 550
- Joined: 04:50 pm May 09 2013
- Country:
- Location: Vermont
Re: eats too much gas & stalls after warming up
Whats the baseline most of us are using ? 155 / 42
05 KDX-220R / 06 KDX-225R / Maxima 927 / Millenium Tech / Ron Black / PC , FMF / Many 220 engine mods / 40 + yrs. of riding dirt bikes
- KDXohio
- Supporting Member
- Posts: 825
- Joined: 06:04 pm Jun 19 2013
- Country: United States
- Location: Dayton, Ohio
Re: eats too much gas & stalls after warming up
Im at 155 / 45 at around 700ft above sea levelC George wrote:Whats the baseline most of us are using ? 155 / 42
1990 KDX200 FMF Fatty, Answer VFC silencer, VForce 3 Cage, Wiseco Piston, KX125-J series KYB USD fork conversion, Race tech goldvalves, J series front brake assembly, air-box snorkel removed, Acerbis Headlight, KX450F Front fender, Pro Taper RM bend bars, ASV front Brake lever, MSR Clutch perch and lever, RB Head mod, 36mm PWK carb, Trail Tech Kickstand.
-
- Supporting Member II
- Posts: 27
- Joined: 10:02 pm Jun 27 2015
- Country:
Re: eats too much gas & stalls after warming up
Jet block gasket deffinetly fixed stalling problem. Thanks, Jullian & everyone else!