Replating story U.S. Chrome - CC DO NOT READ!!
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
Replating story U.S. Chrome - CC DO NOT READ!!
NOT FOR READING BY BRAD
My 00 KTM 380 cylinder was starting to show it age so I sent it off week before Thanksgiving, to US Chrome care of Eric Gorr.
The previous owner had the cylinder intake tracts cleaned and shaped with what was called "trail porting" - leaving a fairly rough surface texture - (no porting timing changes) and had bugged the backside of one of the inlet ports by getting too aggressive with the porting tool - IMHO.
I asked Eric if he would look at this area and weld-up an reshape as necessary prior to having the cylinder replated. (I had run the cylinder this way for 4 years without any problems, but it bothered me every time I performed an R&R and/or R&I on the top end.)
Eric said he would perform an evaluation and heat temper any necessary welds (special procedure for KTMs due to alloys used)
Got back the cylinder Monday and of course took a very good look over everything. The cylinder, porting, and plating look ABSOLUTELY EXCELLENT. He smoothed the previous porter's transitions and cleaned up the area in question; along with reassembling and clearancing the PV. Cylinder bagged in zip lock bag and was spotless making yesterday's reassembly quick and easy.
Purpose of this post? For those of you looking for a replate this winter - this is at least the sixth cylinder that I have sent to U.S. Chrome for replating and have been 100% happy with their work. The key may be sending it to them through Eric Gorr. Just thought I would share!
My 00 KTM 380 cylinder was starting to show it age so I sent it off week before Thanksgiving, to US Chrome care of Eric Gorr.
The previous owner had the cylinder intake tracts cleaned and shaped with what was called "trail porting" - leaving a fairly rough surface texture - (no porting timing changes) and had bugged the backside of one of the inlet ports by getting too aggressive with the porting tool - IMHO.
I asked Eric if he would look at this area and weld-up an reshape as necessary prior to having the cylinder replated. (I had run the cylinder this way for 4 years without any problems, but it bothered me every time I performed an R&R and/or R&I on the top end.)
Eric said he would perform an evaluation and heat temper any necessary welds (special procedure for KTMs due to alloys used)
Got back the cylinder Monday and of course took a very good look over everything. The cylinder, porting, and plating look ABSOLUTELY EXCELLENT. He smoothed the previous porter's transitions and cleaned up the area in question; along with reassembling and clearancing the PV. Cylinder bagged in zip lock bag and was spotless making yesterday's reassembly quick and easy.
Purpose of this post? For those of you looking for a replate this winter - this is at least the sixth cylinder that I have sent to U.S. Chrome for replating and have been 100% happy with their work. The key may be sending it to them through Eric Gorr. Just thought I would share!
KTM 380EXC Mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
- canyncarvr
- Gold Member
- Posts: 6943
- Joined: 01:07 pm Nov 05 2004
- Country: US
- Location: The Mythical State of Jefferson
I did NOT read this....and I never WILL again!
It's good to hear good news once in awhile!!
When riding time comes 'round for you again (what...July or somesuch?) and your bike runs like a pigdog..will you remember the warm and fuzzy (no pun intended) feeling you had LOOKING at it back in the dead of winter?
Yes...I know it's not the dead of winter btw. It hasn't even started yet!
It's good to hear good news once in awhile!!
When riding time comes 'round for you again (what...July or somesuch?) and your bike runs like a pigdog..will you remember the warm and fuzzy (no pun intended) feeling you had LOOKING at it back in the dead of winter?
Yes...I know it's not the dead of winter btw. It hasn't even started yet!
Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis
bike profile: !clicky!
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
Brad - likely not!! I don't expect the bike will run pigdoggy - but cylinder sure looked pretty. Gorr is one of those places like Ron Black's - you send him something to fix and he goes one or two steps beyond what you expected - towards the AWESOME side of things.
ClutchCover and I are both waiting for winter to hit this part of the country - some snow but not enough to really take the sleds out without endangering self and sled with tree stumps and rocks, etc. Likely some localized areas to play, but of course there are those sledders who have 500 -600 miles riding trails since around Turkey Day but I just can not bring myself to ride on beat-up trails that don't lead to a good powder play areas. The other self-limiting self-imposed restriction is that I don't travel over a couple of hours to chase snow. Just hopes it finds us this year!!
ClutchCover and I are both waiting for winter to hit this part of the country - some snow but not enough to really take the sleds out without endangering self and sled with tree stumps and rocks, etc. Likely some localized areas to play, but of course there are those sledders who have 500 -600 miles riding trails since around Turkey Day but I just can not bring myself to ride on beat-up trails that don't lead to a good powder play areas. The other self-limiting self-imposed restriction is that I don't travel over a couple of hours to chase snow. Just hopes it finds us this year!!
KTM 380EXC Mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
- canyncarvr
- Gold Member
- Posts: 6943
- Joined: 01:07 pm Nov 05 2004
- Country: US
- Location: The Mythical State of Jefferson
I consulted my very own 8-ball (you know the shake it up, turn it over thing? I call mine AlGore):
It said: 'Glaciers melting, penguins dying, heartland frozen to death...not likely'
Sorry.
It said: 'Glaciers melting, penguins dying, heartland frozen to death...not likely'
Sorry.
Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis
bike profile: !clicky!
-
- Member
- Posts: 644
- Joined: 11:33 pm Feb 17 2005
- Country:
- Location: Vancouver area, Canada
IC,
As much as I hate to ask personal stuff, (you didn't buy that line of BS?) would you break down, roughly, the cost to have all that work done?
The plating on my 220 was a *little* 'thin' last time I peeked and I wouldn't mind having some idea as to the costs involved when using E G/US Chrome.
Just me ..... and my overwhelming nosiness.
And I certainly appreciate the useful feedback you provided on the work you had done
As much as I hate to ask personal stuff, (you didn't buy that line of BS?) would you break down, roughly, the cost to have all that work done?
The plating on my 220 was a *little* 'thin' last time I peeked and I wouldn't mind having some idea as to the costs involved when using E G/US Chrome.
Just me ..... and my overwhelming nosiness.
And I certainly appreciate the useful feedback you provided on the work you had done
- Ondatrail
- Member
- Posts: 464
- Joined: 03:07 pm Jul 15 2007
- Country:
- Location: Town of Montgomery, NY
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
I already installed it - engine was still in the bike I had just removed the top end. I guess I should have thought about taking a picture, but since there was nothing wrong (which is typically why you take a picture, right?) I put the engine back together and later thought about posting a thread.Ondatrail wrote:A pictures worth a thousand words. I wanna see the job US Crome did, unless you got right on it and its already in the bike.
GS - not a problem. On the invoice '$225 for Nicom cylinder plating, diamond honing, port chamfering, deck lapping and cleaning.' Also he cleaned and reinstalled my PV and set the travel limit on it which is at least as involved as the KIPS KDX valve - this is a normal part of his service (in case you haven't used him before.)
As mentioned in my original note he cleaned up the ports there was not a seperate charge for this. I did not check but I seem to recall the US Chrome website price sheet pricing the plating service at about $200. I suspect that he spent 30 minutes or more on the ports: I did not look at the Forward motion pricing on the web.
Other charges Wieseco piston kit $130 Moose Top Eng Gasket Kit $30 Top End Bearing $15 Shipping Handling Packaging and Insurance $15.
Even though not called out or charged for I also had the necessary 2 Red Silcone O-rings for the head individually packaged in Forward Motion packaging included (one packaged and marked $6.95 the other packaged and marked 5.99) . The red O-rings are typically better O-rings than the black O-rings found in some of the top end kits for KTM on the market - they appear to be the same ones used by KTM as OEM.
So bottom line was $175 for parts (very competitively priced for the KTM BTW) - $225 for the cylinder work - $15 for shipping. Money very well spent IMHO.
P.S. The lower edges on the piston had also been scraped, the cylinder passed the white oil rag test. So it really was a plug and play at assembly time.
KTM 380EXC Mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
-
- Member
- Posts: 644
- Joined: 11:33 pm Feb 17 2005
- Country:
- Location: Vancouver area, Canada
IC - Thanks for the informative reply. Much appreciated. Sounds like you're a happy customer. Pricing seems very fair to me also. I haven't had the opportunity to use either of those two, but might in the future. So, I'll file this away!
AND, your cyl passed the 'ol white rag test! Well, there you go!
You mentioned a scraping of the lower edge of the piston. Not sure what you mean by that, unless you're referring to machining 'burrs' left over that could gouge the wall? I always run my hands all over the things, feeling for edges before assembly...finger nails and all....but haven't ever really found anything that needed attention.
Is that what you are referring to?
Thanks again,
Greg
AND, your cyl passed the 'ol white rag test! Well, there you go!
You mentioned a scraping of the lower edge of the piston. Not sure what you mean by that, unless you're referring to machining 'burrs' left over that could gouge the wall? I always run my hands all over the things, feeling for edges before assembly...finger nails and all....but haven't ever really found anything that needed attention.
Is that what you are referring to?
Thanks again,
Greg
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
Regarding scraping the piston. Pistons tend to rock within the bore as they top out and start there downward motion. A sharp edge on the skirt of the piston will tend to try to scrap or displace the oil barrier which is separating the piston from the wall. A very light relieving (very small bevel) of the outer edge on the piston skirt is thought to reduce this tendency and aid in keeping a film of oil in this critical area.
Mechanics have been doing this for ages.
GS Wrote ....."I haven't had the opportunity to use either of those two, but might in the future. So, I'll file this away!"
Not sure which two companies you are refering to so I just attempt to clarify my understanding of how this works. FYI - Eric Gorr has his own company/shop (Forward Motion) and as you likely know Eric is well recognized in the dirt bike industry.
US Chrome is a company that plates cylinders and has numerous locations world wide. Eric Gorr has endorsed the US Chrome plating process and now has an working association with the local US Chrome plating which is located near Eric's comapny: In that he has an office/work area where he does 'his thing' to cylinders sent to him and oversees or performs specialized repairs. I do not know if he routinely goes to US Chrome i.e. daily or if it is a 2 or 3 time a week approach only that it seems to work well based upon my experience.
Mechanics have been doing this for ages.
GS Wrote ....."I haven't had the opportunity to use either of those two, but might in the future. So, I'll file this away!"
Not sure which two companies you are refering to so I just attempt to clarify my understanding of how this works. FYI - Eric Gorr has his own company/shop (Forward Motion) and as you likely know Eric is well recognized in the dirt bike industry.
US Chrome is a company that plates cylinders and has numerous locations world wide. Eric Gorr has endorsed the US Chrome plating process and now has an working association with the local US Chrome plating which is located near Eric's comapny: In that he has an office/work area where he does 'his thing' to cylinders sent to him and oversees or performs specialized repairs. I do not know if he routinely goes to US Chrome i.e. daily or if it is a 2 or 3 time a week approach only that it seems to work well based upon my experience.
KTM 380EXC Mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
-
- Member
- Posts: 644
- Joined: 11:33 pm Feb 17 2005
- Country:
- Location: Vancouver area, Canada
Thanks for the explanation of scraping...if I understand, there is a slight radius applied to the lower contact area of the skirt so that it 'surfs' the oil film, rather than penetrating and effectively 'plowing' it off the cyl wall?
Never heard of *that* before.....and it just might make sense, to boot! Nice to learn something every day, so thats for passing it on.
I was referring to the EG and US Chrome connection. Sometimes these fairly *demanding* small-shop guys ride shotgun on the work that big outfits do for them. So, EG probably helps to ensure that plating work done on his behalf is done PROPERLY, which could provide a hidden benefit to using his services.
He almost certainly would receive more cooperation than either you or I would, should a problem with the plating arise.
Thanks for the info!!
Never heard of *that* before.....and it just might make sense, to boot! Nice to learn something every day, so thats for passing it on.
I was referring to the EG and US Chrome connection. Sometimes these fairly *demanding* small-shop guys ride shotgun on the work that big outfits do for them. So, EG probably helps to ensure that plating work done on his behalf is done PROPERLY, which could provide a hidden benefit to using his services.
He almost certainly would receive more cooperation than either you or I would, should a problem with the plating arise.
Thanks for the info!!
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
what's that?the cylinder passed the white oil rag test
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
My apology - should have read ...'white rag oil test....
i.e. After cylinder has been honed you clean it up well and the -good to go test - is using a light color cloth or paper towels with some oil to wipe down the cylinder. If after wiping down the complete cylinder your rag is not contaminated with anything other than the oil, then the cylinder is clean enough to install the piston into.
Others ways to check for contamination but this is a common method and your also prepping the cylinder for the piston.
i.e. After cylinder has been honed you clean it up well and the -good to go test - is using a light color cloth or paper towels with some oil to wipe down the cylinder. If after wiping down the complete cylinder your rag is not contaminated with anything other than the oil, then the cylinder is clean enough to install the piston into.
Others ways to check for contamination but this is a common method and your also prepping the cylinder for the piston.
KTM 380EXC Mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
KDX 200 Mark's
TTR 125 L Wife's
KDX 200 Austin's
EC 300 Tyson's
WR430 Husky - mine
-
- Member
- Posts: 644
- Joined: 11:33 pm Feb 17 2005
- Country:
- Location: Vancouver area, Canada
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
After I lightly scoth brite mine I put it in the dishwasher (heard that awhile back on this forum), and was at how fast the rust showed up. Freaked me out, I cleaned again with WD40 asap.you won't see the rust forming as you will with water.
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
-
- Supporting Member II
- Posts: 1005
- Joined: 06:57 pm Mar 19 2005
- Country:
- RBD
- Gold Member
- Posts: 210
- Joined: 02:00 am Jan 18 2005
- Country:
- Location: Portland, Oregon USA
- Contact:
Just a side note here kids, rags are not a good tool to use in final clean-up. Rags will leave threads (or thick lint from the rag it self).
The best final clean-up before assembly is a white paper towel that as been dampened with a light oil like WD-40 or what I like to use is Marvel Mystery Oil. YES, this too will leave a small amount of a much finer lint, but even easer to dispose of.
You will know when the cylinder is clean....., when the white "paper" towel is still white with out any gray showing, it's done
Ron
The best final clean-up before assembly is a white paper towel that as been dampened with a light oil like WD-40 or what I like to use is Marvel Mystery Oil. YES, this too will leave a small amount of a much finer lint, but even easer to dispose of.
You will know when the cylinder is clean....., when the white "paper" towel is still white with out any gray showing, it's done
Ron
-
- Member
- Posts: 644
- Joined: 11:33 pm Feb 17 2005
- Country:
- Location: Vancouver area, Canada
Surely the wife has some nice, clean, white, lint-free dishcloths? HAW!!
Another user of Marvel Mystery Oil! Neat stuff!
I have a friend that slides a drop or two into every tankful of gas in his Cessna 180.....and no finer, smoother-running example of that model exists anywhere.
Good advice about how to know when the clean-up is done and it's time to hide the evidence...even if it is paper towels
Another user of Marvel Mystery Oil! Neat stuff!
I have a friend that slides a drop or two into every tankful of gas in his Cessna 180.....and no finer, smoother-running example of that model exists anywhere.
Good advice about how to know when the clean-up is done and it's time to hide the evidence...even if it is paper towels