Will a standard kx125/250 rim fit on a kdx? I know the rim is a 19 inch and the kdx runs a 18? will this cause a problem? is the hub different??and if so is there a way around that?
thanks
Rim Question
-
- Member
- Posts: 8
- Joined: 09:34 pm Nov 27 2007
- Country:
- Location: VA
Rim Question
stock 2003 kdx220
- krazyinski
- Member
- Posts: 461
- Joined: 12:26 pm Mar 10 2006
- Country:
- Location: San Antonio Texas
depends on year, as far as 2003-2008 the answer is no. looking for a rim?
2000 KDX220 FRP Ported,plated cylinder,milled head, FRP bored carb, V force 3 reeds, FMF desert pipe, 10oz FWW, 98 KX forks and oem shock re valved by Pro Action, hyd clutch, fastway pegs, tall seat foam, gripper cover, 29" CRhigh mini bars, Cycra brush gaurds.
-
- Member
- Posts: 8
- Joined: 09:34 pm Nov 27 2007
- Country:
- Location: VA
- krazyinski
- Member
- Posts: 461
- Joined: 12:26 pm Mar 10 2006
- Country:
- Location: San Antonio Texas
no but you could lace the rear rim to the kdx hub.
I have a new excel black with spline drive spokes on a KDX hub I will sell or buy the kx set on ebay and trade the rear for mine.
I have a new excel black with spline drive spokes on a KDX hub I will sell or buy the kx set on ebay and trade the rear for mine.
2000 KDX220 FRP Ported,plated cylinder,milled head, FRP bored carb, V force 3 reeds, FMF desert pipe, 10oz FWW, 98 KX forks and oem shock re valved by Pro Action, hyd clutch, fastway pegs, tall seat foam, gripper cover, 29" CRhigh mini bars, Cycra brush gaurds.
- canyncarvr
- Gold Member
- Posts: 6943
- Joined: 01:07 pm Nov 05 2004
- Country: US
- Location: The Mythical State of Jefferson
I looked...didn't see the wheel on the 'parts' section? I missed it? No? Going to post it?
I presume the rim is true?
Any other particulars about it? What's in it for bearings? CBR, right?
I presume the rim is true?
Any other particulars about it? What's in it for bearings? CBR, right?
Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis
bike profile: !clicky!
- krazyinski
- Member
- Posts: 461
- Joined: 12:26 pm Mar 10 2006
- Country:
- Location: San Antonio Texas
I was thinking of keeping the rim and lacing the oem rim back to it but at the rate of money going out, I could use some coming in.
so no I have not posted it yet.
THE CONDITION OF THE RIM AND SPOKES ARE NEW AND TRUE.
THE BEARINGS AND SEALS HAVE HAD THERE SHARE OF ABUSE
I HAVE BEEN BUSY WITH THE KX AND HAVE NOT LOOKED AT THE BEARINGS
ON THE KDX HUB.
I WOULD THINK THEY ARE IN NEED OF CLEANING AND RE PACK.
I know they are sealed bearings, I just pop the seals off clean, pack and pop the seals back on.
so I know the bearings are a couple years old.
so no I have not posted it yet.
THE CONDITION OF THE RIM AND SPOKES ARE NEW AND TRUE.
THE BEARINGS AND SEALS HAVE HAD THERE SHARE OF ABUSE
I HAVE BEEN BUSY WITH THE KX AND HAVE NOT LOOKED AT THE BEARINGS
ON THE KDX HUB.
I WOULD THINK THEY ARE IN NEED OF CLEANING AND RE PACK.
I know they are sealed bearings, I just pop the seals off clean, pack and pop the seals back on.
so I know the bearings are a couple years old.
2000 KDX220 FRP Ported,plated cylinder,milled head, FRP bored carb, V force 3 reeds, FMF desert pipe, 10oz FWW, 98 KX forks and oem shock re valved by Pro Action, hyd clutch, fastway pegs, tall seat foam, gripper cover, 29" CRhigh mini bars, Cycra brush gaurds.
- canyncarvr
- Gold Member
- Posts: 6943
- Joined: 01:07 pm Nov 05 2004
- Country: US
- Location: The Mythical State of Jefferson
Repacking 1/2" marbles in a 1" race...
Time to Call Charlie!! Lifetime guarantee!!!
You can send me the wheel, I'll test it with CBRs and let you know how it works!!
Time to Call Charlie!! Lifetime guarantee!!!
You can send me the wheel, I'll test it with CBRs and let you know how it works!!
Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis
bike profile: !clicky!