Torque Wrench range
- stringburner
- Supporting Member III
- Posts: 221
- Joined: 06:18 pm Oct 12 2006
- Country:
Torque Wrench range
Would two wrenchs that handle torque values in the 20 in. lb.~120 ft. lb. range handle these bikes applications?
- Jeb
- Gold Member
- Posts: 1894
- Joined: 08:01 pm Jul 14 2006
- Country:
- Location: Cincinnati / Northern Kentucky
I looked up the recommended torque settings for various fasteners. The highest torque is for the rear axle nut @ 72 ft-lb. More than half of the settings are less than 30 ft-lb.
I bought one 3/8" drive torque wrench and I believe it should cover those needs. 'Might be advantageous to to get some of the "crows foot" adapters for hard-to-reach areas (on the cylinder base nuts it's a must) - a good metric set will run you about $35 and they are very handy.
I believe some get around the adapters with some creative welding (do a search). IMHO having the tools is nice.
'Hope this helps!!
BTW - how 'bout them Mountaineers!!
I bought one 3/8" drive torque wrench and I believe it should cover those needs. 'Might be advantageous to to get some of the "crows foot" adapters for hard-to-reach areas (on the cylinder base nuts it's a must) - a good metric set will run you about $35 and they are very handy.
I believe some get around the adapters with some creative welding (do a search). IMHO having the tools is nice.
'Hope this helps!!
BTW - how 'bout them Mountaineers!!
- stringburner
- Supporting Member III
- Posts: 221
- Joined: 06:18 pm Oct 12 2006
- Country:
Thanks Jeb. I think i'll get one for inch pounds and one for foot pounds....Or I might look up some conversions and see if the inch pound one will handle the foot pound requirements.
The Mountaineers...I have mixed feelings about that. You always like to see your states team do well, but their schedule is a patsy. They should never have been ranked as highly as they were w/ the opponents they face. I was tickled when Lewavuhl gave 'em a good adjustin'. I recall one year they were all high and mighty, had a perfect season, and then went to some fancy bowl, actually played a team w/ talent (Florida or Florida State I think), and got their asses handed to them. Funny stuff.
Oh yeah, I was perusing the Craftsman tool catalog and saw an adapter, you put in betwixt your ratchet/breaker bar, and your socket, and it acts as a torque wrench. It reads in inch, foot, or Nm. Looks might nice, but kind of pricey @ $200.00.
The Mountaineers...I have mixed feelings about that. You always like to see your states team do well, but their schedule is a patsy. They should never have been ranked as highly as they were w/ the opponents they face. I was tickled when Lewavuhl gave 'em a good adjustin'. I recall one year they were all high and mighty, had a perfect season, and then went to some fancy bowl, actually played a team w/ talent (Florida or Florida State I think), and got their asses handed to them. Funny stuff.
Oh yeah, I was perusing the Craftsman tool catalog and saw an adapter, you put in betwixt your ratchet/breaker bar, and your socket, and it acts as a torque wrench. It reads in inch, foot, or Nm. Looks might nice, but kind of pricey @ $200.00.
- Jeb
- Gold Member
- Posts: 1894
- Joined: 08:01 pm Jul 14 2006
- Country:
- Location: Cincinnati / Northern Kentucky
- Colorado Mike
- Gold Member
- Posts: 1921
- Joined: 11:42 am Feb 25 2005
- Country:
- Location: Colorado
- stringburner
- Supporting Member III
- Posts: 221
- Joined: 06:18 pm Oct 12 2006
- Country: