Hi dumb question but does any one know the length for a H rear axel spacers and which side is the shortest (right I presme)
Reason is, I'm building my hybrid (2001 KX125) and between getting the doner in parts, cleaning the KDX parts and other I have ended up with:
2 x 22mm
2 x 20mm
1 x 19mm
And haven't a clue as to which ones fit the KX.
I have measured the hub with and sistance between swing arm but don't know how much take up is required.
My theory is if I can take the KDX ones out of the mix it will narrow it down?
Thanks
Rear axel spacer question
- Tioli
- Supporting Member I
- Posts: 267
- Joined: 06:57 am Jul 19 2014
- Country: Tasmania AUS
Rear axel spacer question
2001 KX125 with a 1997 KDX Tioli Hp motor
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
-
- Supporting Member III
- Posts: 1484
- Joined: 02:26 pm Jun 29 2005
- Country:
- Location: Alabama
Re: Rear axel spacer question
I did not think the KX and KDX had the same diameter rear axle.
Obviously they do, or you would not be asking.
Sorry I can't answer your question.
Obviously they do, or you would not be asking.
Sorry I can't answer your question.
'08 KTM200xc
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
-
- Gold Member
- Posts: 821
- Joined: 10:00 am May 29 2012
- Country:
- Location: Spring Grove, Illinois
Rear axel spacer question
Can't answer either. In messing around with fitting a reinforced (thicker around the axle) Devol rotor guard, I ended up doing a cut-and-try spacer fit when trying to put everything back together. Also had to shim the caliper holder to get everything to line up properly. Fortunately, I have a lathe so this work wasn't too difficult for me.
- Tioli
- Supporting Member I
- Posts: 267
- Joined: 06:57 am Jul 19 2014
- Country: Tasmania AUS
Rear axel spacer question
Thanks so far. They are all the same Ida. They look the same except for the slight diference in length.
If all else fails I can play with combinations and free spin the wheel to see if the chain has a bias to run to either side of the sprockets.
Can't say it's my preferred option hence the post.
If all else fails I can play with combinations and free spin the wheel to see if the chain has a bias to run to either side of the sprockets.
Can't say it's my preferred option hence the post.
2001 KX125 with a 1997 KDX Tioli Hp motor
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
-
- Supporting Member I
- Posts: 567
- Joined: 10:38 am Aug 20 2012
- Country:
- Location: anderson sc
Re: Rear axel spacer question
I have a 2000 kx hybrid and both rear spacers are 20mm
- Tioli
- Supporting Member I
- Posts: 267
- Joined: 06:57 am Jul 19 2014
- Country: Tasmania AUS
Rear axel spacer question
Fantastic thank you.
I justl checked and the 2000 and 2001 have the same part numbers and I'm done
I justl checked and the 2000 and 2001 have the same part numbers and I'm done
2001 KX125 with a 1997 KDX Tioli Hp motor
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160
Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9