Rear axel spacer question

Got questions? We got answers....

Rear axel spacer question

Postby Tioli » 05:39 pm Dec 11 2014

Hi dumb question but does any one know the length for a H rear axel spacers and which side is the shortest (right I presme)

Reason is, I'm building my hybrid (2001 KX125) and between getting the doner in parts, cleaning the KDX parts and other I have ended up with:
2 x 22mm
2 x 20mm
1 x 19mm
And haven't a clue as to which ones fit the KX.
I have measured the hub with and sistance between swing arm but don't know how much take up is required.
My theory is if I can take the KDX ones out of the mix it will narrow it down?
Thanks
2001 KX125 with a 1997 KDX Tioli Hp motor

My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160

Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
User avatar
Tioli
Supporting Member I
Supporting Member I
 
Posts: 267
Images: 1
Joined: 06:57 am Jul 19 2014
Has thanked: 1 time
Been thanked: 10 times

Re: Rear axel spacer question

Postby KarlP » 07:58 am Dec 12 2014

I did not think the KX and KDX had the same diameter rear axle.

Obviously they do, or you would not be asking.

Sorry I can't answer your question.
'08 KTM200xc
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
KarlP
Supporting Member III
Supporting Member III
 
Posts: 1484
Images: 6
Joined: 02:26 pm Jun 29 2005
Location: Alabama
Has thanked: 0 time
Been thanked: 7 times

Rear axel spacer question

Postby pumpguy » 04:40 pm Dec 12 2014

Can't answer either. In messing around with fitting a reinforced (thicker around the axle) Devol rotor guard, I ended up doing a cut-and-try spacer fit when trying to put everything back together. Also had to shim the caliper holder to get everything to line up properly. Fortunately, I have a lathe so this work wasn't too difficult for me.
pumpguy
Gold Member
Gold Member
 
Posts: 643
Joined: 10:00 am May 29 2012
Location: Spring Grove, Illinois
Has thanked: 40 times
Been thanked: 49 times

Rear axel spacer question

Postby Tioli » 10:31 pm Dec 12 2014

Thanks so far. They are all the same Ida. They look the same except for the slight diference in length.

If all else fails I can play with combinations and free spin the wheel to see if the chain has a bias to run to either side of the sprockets.

Can't say it's my preferred option hence the post.
2001 KX125 with a 1997 KDX Tioli Hp motor

My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160

Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
User avatar
Tioli
Supporting Member I
Supporting Member I
 
Posts: 267
Images: 1
Joined: 06:57 am Jul 19 2014
Has thanked: 1 time
Been thanked: 10 times

Re: Rear axel spacer question

Postby royadams » 01:06 pm Dec 13 2014

I have a 2000 kx hybrid and both rear spacers are 20mm
royadams
Supporting Member I
Supporting Member I
 
Posts: 567
Joined: 10:38 am Aug 20 2012
Location: anderson sc
Has thanked: 2 times
Been thanked: 20 times

Rear axel spacer question

Postby Tioli » 05:01 pm Dec 13 2014

Fantastic thank you.
I justl checked and the 2000 and 2001 have the same part numbers and I'm done :boogie:
2001 KX125 with a 1997 KDX Tioli Hp motor

My KDX journey starts at the bottom of this page:
http://www.trials.com.au/forum/viewtopi ... &start=160

Trials.com.au / Forum / All about...me! / My long time friend the prancing horse / page 9
User avatar
Tioli
Supporting Member I
Supporting Member I
 
Posts: 267
Images: 1
Joined: 06:57 am Jul 19 2014
Has thanked: 1 time
Been thanked: 10 times


Return to KDX General Q&A

Who is online

Users browsing this forum: Bing [Bot] and 3 guests