Bent KIPS pin
-
- Supporting Member III
- Posts: 1484
- Joined: 02:26 pm Jun 29 2005
- Country:
- Location: Alabama
Bent KIPS pin
Hey all-
Does anyone know a good source for the pin that engages the KIPS centrifugal doohicky down in the right side, above the water pump?
A buddy of mine has been putting a hybrid together. It has been going well. He had concerns about the KIPS valve timing so I took a look and found that at some point the pin was bent. There was no way the pawl gear was going to go on coreectly.
I'll need right side gasket, clutch cover gasket and that pin thing.
Thanks for any help
Does anyone know a good source for the pin that engages the KIPS centrifugal doohicky down in the right side, above the water pump?
A buddy of mine has been putting a hybrid together. It has been going well. He had concerns about the KIPS valve timing so I took a look and found that at some point the pin was bent. There was no way the pawl gear was going to go on coreectly.
I'll need right side gasket, clutch cover gasket and that pin thing.
Thanks for any help
'08 KTM200xc
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
-
- Member
- Posts: 54
- Joined: 04:02 am Jul 26 2011
- Country:
Re: Bent KIPS pin
Would a roll pin work?
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
Bent KIPS pin
replace it, if it's bent it's gonna break later.
I get mine from ronayers, bike bandit, or service honda.
I get mine from ronayers, bike bandit, or service honda.
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
- 6 Riders
- Gold Member
- Posts: 2124
- Joined: 12:58 pm May 01 2013
- Country: USA
- Location: Washington
- Contact:
Bent KIPS pin
These are sill available....buy 2 they are cheap...errr... inexpensive!scheckaet wrote:replace it, if it's bent it's gonna break later.
I get mine from ronayers, bike bandit, or service honda.
newbbewb wrote:^what he said.
*side note...I'm drunk, so try to read what I'm trying to say, instead of what I actually typemasterblaster wrote:Man 6 riders you rock.
- diymirage
- Supporting Member II
- Posts: 2909
- Joined: 05:00 pm Sep 19 2011
- Country:
- Location: michigan
Re: Bent KIPS pin
I get mine from rockymountainORV
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
newbbewb wrote:DIYmirage has it right.
-1996 KDX 200 woods weapon (converted to 99 green body)
-1996 KDX 200 plated street toy (barney edition)
-2003 Yamaha TTR125-L (wifeys bike)
-1997 KDX 220 project bike
- 6 Riders
- Gold Member
- Posts: 2124
- Joined: 12:58 pm May 01 2013
- Country: USA
- Location: Washington
- Contact:
Re: Bent KIPS pin
Me too!diymirage wrote:I get mine from rockymountainORV
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
newbbewb wrote:^what he said.
*side note...I'm drunk, so try to read what I'm trying to say, instead of what I actually typemasterblaster wrote:Man 6 riders you rock.
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
Re: Bent KIPS pin
bahhhhhh! you dumb shiii...oh wait, i do the same. so you mean you don't HAVE to spend 100$ when you place an order?????diymirage wrote:I get mine from rockymountainORV
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
- bufftester
- Platinum Member
- Posts: 3459
- Joined: 06:03 pm Oct 31 2012
- Country: USA
- Location: University Place, WA
Re: Bent KIPS pin
Crap, should have read this before my latest order to Motosports. I needed $10 of hardware for my GSX-R, ended up with $93 of other stuff so I could save the $6 shipping!scheckaet wrote:bahhhhhh! you dumb shiii...oh wait, i do the same. so you mean you don't HAVE to spend 100$ when you place an order?????diymirage wrote:I get mine from rockymountainORV
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
- diymirage
- Supporting Member II
- Posts: 2909
- Joined: 05:00 pm Sep 19 2011
- Country:
- Location: michigan
Re: Bent KIPS pin
scheckaet wrote:bahhhhhh! you dumb shiii...oh wait, i do the same. so you mean you don't HAVE to spend 100$ when you place an order?????diymirage wrote:I get mine from rockymountainORV
the only downside is that I always add 97 dollars in other stuff to my order to get free shipping
it actually comes from the "should stock up on....list"
tubes, spark plugs, oil, filters, tires, the usual
stuff you go through on a regular basis
newbbewb wrote:DIYmirage has it right.
-1996 KDX 200 woods weapon (converted to 99 green body)
-1996 KDX 200 plated street toy (barney edition)
-2003 Yamaha TTR125-L (wifeys bike)
-1997 KDX 220 project bike
-
- Member
- Posts: 44
- Joined: 11:40 pm Dec 02 2012
- Country:
- Location: Woods
Bent KIPS pin
Are you talking about the governor shaft or the lever at the end of the shaft? OR the little pin that holds the governor shaft in? The governor shaft is what the claw gear connects to and it's about $75 bucks. THe lever on the end of the governor shaft (inside the case) is ~$10.
'04 KDX 200
'01 KDX 200 (current project)
'01 KDX 200 (current project)
-
- Supporting Member III
- Posts: 1484
- Joined: 02:26 pm Jun 29 2005
- Country:
- Location: Alabama
Re: Bent KIPS pin
The lever at the end of the shaft. I bought it and a few gaskets
Bent like it was the exhaust valves could not be timed properly. Looking at the wear marks it had been run like that for a while.
Bent like it was the exhaust valves could not be timed properly. Looking at the wear marks it had been run like that for a while.
'08 KTM200xc
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
'99 CR/KDX Hybrid with that RB stuff done to it
KX100 for the boy
-
- Member
- Posts: 1
- Joined: 03:30 pm Oct 13 2012
- Country:
Bent KIPS pin
I too have had to replace that small pin. Also I buy it from Rocky Mountain ATV as mentioned above. Great service, great source of oem kdx parts ,awesome points program, excellent shipping.
One thing I want to mention is if that pin breaks it tends to get into the transmissionn. There is a little Oil port at the top of the engine case that flows oil back into the transmission side and when that pin brakes because of the way everything is rotating inside it gets flung right up to that port drops right down into the gears and you are dead in your tracks. I had it happened to my personal bike which totally chewed up a couple gears inside. And a friends KDX did the exact same thing he took a jump hit the ground and when it fell into the transmission it locked the bike up, he almost went over the handlebars because it stopped him so hard.
So don't even think about it, buy the part replace it it's only nine dollars and buy an extra one also so that at a maintenance interval you can take it apart and replace it just to be safe.
One thing I want to mention is if that pin breaks it tends to get into the transmissionn. There is a little Oil port at the top of the engine case that flows oil back into the transmission side and when that pin brakes because of the way everything is rotating inside it gets flung right up to that port drops right down into the gears and you are dead in your tracks. I had it happened to my personal bike which totally chewed up a couple gears inside. And a friends KDX did the exact same thing he took a jump hit the ground and when it fell into the transmission it locked the bike up, he almost went over the handlebars because it stopped him so hard.
So don't even think about it, buy the part replace it it's only nine dollars and buy an extra one also so that at a maintenance interval you can take it apart and replace it just to be safe.