91 KDX200 float height

Got questions? We got answers....
Post Reply
200Scrambler
Member
Posts: 26
Joined: 11:06 am Apr 13 2013
Country:

91 KDX200 float height

Post by 200Scrambler »

I'm planning on cleaning my carb in my 91 KDX200 and I wanted to make sure the float what set right, does anybody know that stock height for it?
whc
Member
Posts: 41
Joined: 03:02 pm May 02 2013
Country:
Location: Hermon NY

Re: 91 KDX200 float height

Post by whc »

good question, I just set my 94 so that it shuts just before the floats are level. same as I would do with my hondas.
Thrahl
Member
Posts: 222
Joined: 08:51 am May 30 2012
Country:

Re: 91 KDX200 float height

Post by Thrahl »

The manual says 16 +- 1mm. Here's a pic.
Image
200Scrambler
Member
Posts: 26
Joined: 11:06 am Apr 13 2013
Country:

Re: 91 KDX200 float height

Post by 200Scrambler »

What does it mean by 16 + 1mm? I'm new to this
200Scrambler
Member
Posts: 26
Joined: 11:06 am Apr 13 2013
Country:

Re: 91 KDX200 float height

Post by 200Scrambler »

What does it mean by 16 + 1mm? I'm new to this
Thrahl
Member
Posts: 222
Joined: 08:51 am May 30 2012
Country:

Re: 91 KDX200 float height

Post by Thrahl »

Look at the float height measurement section on that page. You want the number 4 measurement to be between 15 and 17 mm.
Follow the directions from that section and the note right below it and you will be fine.
200Scrambler
Member
Posts: 26
Joined: 11:06 am Apr 13 2013
Country:

91 KDX200 float height

Post by 200Scrambler »

I adjusted my float but still nothing. I sit there and kick and kick and kick. Sometimes it will spill gas out of the overflow tube from the carb. Think maybe a spark plug?
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: 91 KDX200 float height

Post by KDXGarage »

dirty valve needle?
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
200Scrambler
Member
Posts: 26
Joined: 11:06 am Apr 13 2013
Country:

Re: 91 KDX200 float height

Post by 200Scrambler »

Like, float needle? When I looked at it, it wasn't dirty. I cleaned the whole carb up and down.
User avatar
KDXGarage
KDXRider.net
KDXRider.net
Posts: 14047
Joined: 06:45 am Nov 01 2004
Country: United States of America
Location: AL, USA
Contact:

Re: 91 KDX200 float height

Post by KDXGarage »

It is the cone shaped, rubber tipped piece that is supposed to stop the flow of fuel into the bowl. A dirty/damaged bore or dirty/damaged rubber tip can cause a leak.
Thank you for participating on kdxrider.net. :bravo:
To post pictures from a device: viewtopic.php?f=88&t=24128
whc
Member
Posts: 41
Joined: 03:02 pm May 02 2013
Country:
Location: Hermon NY

Re: 91 KDX200 float height

Post by whc »

thank for the info. diagram is great help. scrambler if your getting gas to the carb u may want to check the plug. bill
Post Reply