Hi guys,
I've noticed that my rear pads are rubbing, so I've decided to clean out the relief port on the master cylinder. However I'm having trouble removing the connector (where the feed from the resevoir fits over) from the master cylinder. I have removed the circlip, but cant remove the connector it self. I'm scared if I pull it to hard it will break. Any tips?
Thanks!
Removing Rear Master Cylinder connector
-
- Member
- Posts: 6
- Joined: 12:49 pm May 26 2010
- Country:
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
Removing Rear Master Cylinder connector
have you replaced the pad holding pin with a new one?
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
-
- Member
- Posts: 6
- Joined: 12:49 pm May 26 2010
- Country:
Removing Rear Master Cylinder connector
I actually came right with the connector. No, I am going to try get a set tomorrow, I heard it could be another reason for the pads sticking.
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
Removing Rear Master Cylinder connector
most of the time, the pin is worn out slightly (can't see it) and the pads will wear out a lot faster.
I burnt a new set in less than 10-15 miles because of that. I inspected it several times and it looked good (even sanded it to make it perfectly smooth) but in the end, a new pin solved my problem.
I burnt a new set in less than 10-15 miles because of that. I inspected it several times and it looked good (even sanded it to make it perfectly smooth) but in the end, a new pin solved my problem.
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
-
- Member
- Posts: 6
- Joined: 12:49 pm May 26 2010
- Country:
Removing Rear Master Cylinder connector
Thanks! I saw there was a slight groove! Any thanks for the advice