Kips gov. bearing
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Kips gov. bearing
Anyone ever get this fugger out easily?
Inner diameter is 8mm
Inner diameter is 8mm
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
Yup.
If you take a 1/4" bolt a few inches long and attach the threaded end to your slid hammer some how ( weld it to a nut or if you have an adapter to thread it into ) then grind down the hex head leaving a lip on about half of it until it will fit in the hole You will need to also relieve some of the bolt diameter to let the lip to clear the bearing. You can catch the edge of the bolt on the edge of the bearing and pop it out. Or you can buy the $200 kit that is made to do it, but the one that I had didn't have a puller tip that would fit so that may not work.
I don't have the "tool" that I made at my house but I can get it if you need a picture.
If you take a 1/4" bolt a few inches long and attach the threaded end to your slid hammer some how ( weld it to a nut or if you have an adapter to thread it into ) then grind down the hex head leaving a lip on about half of it until it will fit in the hole You will need to also relieve some of the bolt diameter to let the lip to clear the bearing. You can catch the edge of the bolt on the edge of the bearing and pop it out. Or you can buy the $200 kit that is made to do it, but the one that I had didn't have a puller tip that would fit so that may not work.
I don't have the "tool" that I made at my house but I can get it if you need a picture.
- kdxmaniac
- Supporting Member
- Posts: 595
- Joined: 09:01 pm May 24 2010
- Country:
this is the kit ive got. works great, and comes with a 8mm.
http://www.mactools.com/SearchResults/t ... =mn08-0292
http://www.mactools.com/SearchResults/t ... =mn08-0292
my bikes
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
- kdxmaniac
- Supporting Member
- Posts: 595
- Joined: 09:01 pm May 24 2010
- Country:
heres one thats alot cheaper, and really the same thing.
http://www.rockymountainatvmc.com/produ ... lyId=20342
http://www.rockymountainatvmc.com/produ ... lyId=20342
my bikes
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Talking big $$ for a $2 bearing
Hopefully I can find someone with a puller
there's only about a mm or less of space behind the bearing
The inner bearing for the water pump shaft is 6mm, I'd like to get it too
spose you could tack weld something to the bearing and get it with a slide hammer. But I have neither a welder nor a slide hammer
Hopefully I can find someone with a puller
there's only about a mm or less of space behind the bearing
The inner bearing for the water pump shaft is 6mm, I'd like to get it too
spose you could tack weld something to the bearing and get it with a slide hammer. But I have neither a welder nor a slide hammer
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
You can make a slide hammer out of just about any thing. Threaded rod and something heavy.Mr. Wibbens wrote:Talking big $$ for a $2 bearing
Hopefully I can find someone with a puller
there's only about a mm or less of space behind the bearing
The inner bearing for the water pump shaft is 6mm, I'd like to get it too
spose you could tack weld something to the bearing and get it with a slide hammer. But I have neither a welder nor a slide hammer
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
how about heating the case a bit a putting some dry ice on the bearing? might be enough to get it looser and remove it with a screwdriver or sumthin.
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
- kdxmaniac
- Supporting Member
- Posts: 595
- Joined: 09:01 pm May 24 2010
- Country:
you can also use concrete ancors. get one the size you need, put the bolt in a body slide hammer, and there you go.
my bikes
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
-------------
96 ktm 300
96 XR400R
07 hayabusa
77 kz 1000
85 goldwing 1200
02 BIG DOG PITBULL
gone but not forgotten
96 kdx 200
98 ktm 380 "because it dang near killed me!"
97 ktm 360
96 ktm 250
93 wr 250
94 dr 350s
93 kx 250
07 gsxr 1000
99 bandit 1200
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
A friend already suggested that
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Had an "Ohh duh!" moment
I was applying heat here
Instead of here
Heated the case around the bearing and shot it with some canned air and then slammed it down on a wooden bench, popped right out!
I was applying heat here
Instead of here
Heated the case around the bearing and shot it with some canned air and then slammed it down on a wooden bench, popped right out!
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- scheckaet
- KDXRider.net
- Posts: 3740
- Joined: 12:09 am Nov 10 2005
- Country:
- Location: edmond oklahoma
02 KX 200 hybrid: RB head and carb
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
Sold ☹ DRZ 400 SM
bike build: http://www.kdxrider.net/forums/viewtopi ... ike+stable
bike profile http://www.kdxrider.net/forums/viewtopi ... 0709#30709
newb info: http://www.kdxrider.net/forums/viewtopi ... 57#p117919
jetting guide: http://www.kdxrider.net/forums/viewtopi ... 105&t=1156
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Still making bad noises
Pull top end next
Pull top end next
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Replaced everything in bottom end last year except the rod bearings
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Had no reason to, it checked out fine
Plus I had neither the time nor the money to do anything more
I had a day to get the bottom end done before a big ride/camp out
Plus I had neither the time nor the money to do anything more
I had a day to get the bottom end done before a big ride/camp out
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- rbates9
- Supporting Member II
- Posts: 3164
- Joined: 06:07 pm Apr 27 2010
- Country:
- Location: UPSTATE New York
- Mr. Wibbens
- KDXRider.net
- Posts: 4884
- Joined: 02:57 am Nov 07 2004
- Country:
- Location: Playing in the Poison Oak
- Contact:
Found it
Warning! This member tends to use sarcasm as a regular form of communication. If a post seems offensive, before you panic and fly off the handle, re-read the post and imagine it being said with a sideways grin.
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
((Bike Profile))
((Pics))
FIVE OUT OF FOUR PEOPLE DONUT UNDERSTAND FRACTIONS
- Julien D
- KDXRider.net
- Posts: 5858
- Joined: 07:53 pm Nov 07 2008
- Country: USA
- Contact:
- TWMOODY
- Gold Member
- Posts: 752
- Joined: 08:10 pm Dec 01 2006
- Country:
- Location: Southeast , Michigan
Re: Kips gov. bearing
[quote="Mr. Wibbens"]Anyone ever get this fugger out easily?
Next time take and pack that hole flush with grease and find a bolt or round stock that fits tight inside the bearing and hit it with a hammer. Refill with grease after each hit. Two or three times and it's out.
All your doing is pressing the bearing out using the grease.
Used to do the same thing with pilot bearings and bushings.
Next time take and pack that hole flush with grease and find a bolt or round stock that fits tight inside the bearing and hit it with a hammer. Refill with grease after each hit. Two or three times and it's out.
All your doing is pressing the bearing out using the grease.
Used to do the same thing with pilot bearings and bushings.