Page 1 of 1
Handlebar Bends
Posted: 12:33 pm Mar 14 2011
by ejweick
What are you favorites? I'm thinking about a Protaper CR hi, or Henry/Reed. I think I like the CR hi the best.
Posted: 01:37 pm Mar 14 2011
by Julien D
Running a cut down cr hi on mine. I like it pretty good.
Posted: 01:42 pm Mar 14 2011
by ejweick
How much did shorten it?
Posted: 02:42 pm Mar 14 2011
by Julien D
I cut it down to 28". I think it was 31.5".
Posted: 05:07 am Mar 15 2011
by makeshoes
i'm running CR Hi myself. cut off 1/2" from each end this winter!
Posted: 06:33 am Mar 15 2011
by Tedh98
Have you guys ever seen a website that shows the different bends side by side? The local motorcycle shops don't stock very many dirt bike parts, so I don't have an easy way to compare one bend to another.
I've found a few pictures of different bars together, but it doesn't indicate what bar is what bend.
Posted: 10:20 am Mar 15 2011
by Julien D
no, but you can get an idea from the measurements of the bars. Rise, sweep, width.
Posted: 10:48 am Mar 15 2011
by scheckaet
RMATV has a section on bar bends, dunno if it'll help but just fyi
Posted: 11:01 am Mar 15 2011
by ejweick
I'm not trying to advertise but the Cycle Gear store near me has about a dozen different bars on display. My son has inherited my KDX 200. He says he wants the Protaper Henry/Reed in gray. I'm goin to pick one up for his birtyday next month. His uncle gave him a set of Cycra Probend hand guards.
Posted: 04:28 pm Mar 15 2011
by SS109
scheckaet wrote:RMATV has a section on bar bends, dunno if it'll help but just fyi
RMATV's bar charts are what I used to figure out what bend I wanted. I got as close a bend to the factory Renthals and it turned out to be the YZ/WR bend.
Posted: 04:49 pm Mar 15 2011
by Mr. Wibbens
If you buy mini bars you don't have to cut them down
Posted: 05:17 pm Mar 15 2011
by Julien D
Mr. Wibbens wrote:If you buy mini bars you don't have to cut them down
Yes, indeed. I hear the yz80 bend is pretty good.
Posted: 10:59 pm Mar 15 2011
by Velocity_Stack
I didn't know what bend my bike had when I bought it, so I looked at RMATV's bend chart and compared.
The closest bend to the Renthals already on the bike was the KX low, so I bought some low budget MSRs......... hope I never have to find out how stout they are...
Posted: 11:09 pm Mar 15 2011
by Mr. Wibbens
Velocity_Stack wrote:I didn't know what bend my bike had when I bought it, so I looked at RMATV's bend chart and compared.
The closest bend to the Renthals already on the bike was the KX low, so I bought some low budget MSRs......... hope I never have to find out how stout they are...
Better keep in in the garage then
Posted: 12:29 am Mar 16 2011
by Velocity_Stack
Mr. Wibbens wrote:Velocity_Stack wrote:I didn't know what bend my bike had when I bought it, so I looked at RMATV's bend chart and compared.
The closest bend to the Renthals already on the bike was the KX low, so I bought some low budget MSRs......... hope I never have to find out how stout they are...
Better keep in in the garage then
LOL, guess I left the door wide open for that one!
I'm just not looking forward to the first spill and the bars not holding up - which will make me wish I had dropped $60 into a better set.
I would love to invest in the 1 1/8" setup, but it appears to a pain in the rump - gathering parts and pieces to make it all work.
Posted: 12:38 am Mar 16 2011
by Mr. Wibbens
I paid $20 for my renthals off of Craigs List
Saw some Fat Bars the other day for $30
I've got Roxx Risers, they'll accept both 7/8 and 1 1/8 bars
I tried the cheap bar route, it just sucks dealing with wonky bars all the time
These Renthals are stout, I've yet to tweak them
I run Fat Bars on my street bike. I've lowsided on both sides and stuck my handlebar through the door of a truck, and they are straight as the day I bought them
Posted: 06:13 am Mar 16 2011
by Julien D
I'm using the tusk chub 1 1/8 bar. It was seriously cheap. $30 or something I think? Have taken some pretty hard spills and they are still straight.