Page 1 of 2
Newb carb question vm34
Posted: 11:59 pm Apr 05 2020
by Michael93
Sorry may be a silly question but what's holes are for what etc I'm unsure
Re: Newb carb question vm34
Posted: 12:09 am Apr 06 2020
by KDXGarage
WHAT THE HE**?!
Does it have an oil tank for the two-stroke oil??
top pic, upper left is a vent hose location, I suppose
MAN! That is different than the USA carb!
Re: Newb carb question vm34
Posted: 12:15 am Apr 06 2020
by Michael93
Oh really I'm confused now haha, now no oil tank just mix in with the fuel,
Re: Newb carb question vm34
Posted: 12:18 am Apr 06 2020
by KDXGarage
lemme look around
maybe that second brass part is just a vent connection?
Re: Newb carb question vm34
Posted: 12:22 am Apr 06 2020
by Michael93
1
Re: Newb carb question vm34
Posted: 12:24 am Apr 06 2020
by KDXGarage
Yeah, I think it is just a vent. One on each side, then one on the bowl (overflow).
Man. My eyes were tricking me. :-0
Re: Newb carb question vm34
Posted: 12:28 am Apr 06 2020
by Michael93
Same here I dont remeber anymore than two hoses on my old one
I guess if it's running wrong when I start it I'll just putting my finger over holes lol
Re: Newb carb question vm34
Posted: 12:34 am Apr 06 2020
by Michael93
This is mine and from here they looked to be blocked of unlike the new one they are open hmmm
Re: Newb carb question vm34
Posted: 12:51 am Apr 06 2020
by KDXGarage
OK, now that one looks normal to me.
Re: Newb carb question vm34
Posted: 12:54 am Apr 06 2020
by Michael93
So if it doesn't run properly I'll lock then an see will let you know results ha
Re: Newb carb question vm34
Posted: 02:32 am Apr 06 2020
by Michael93
More problems gahhh
Re: Newb carb question vm34
Posted: 03:34 am Apr 06 2020
by KDXGarage
Hang in there!
Re: Newb carb question vm34
Posted: 03:42 am Apr 06 2020
by Michael93
I am sorta, so it's got a 6f39 needle so now I need to research and find excately what carb I have, maybe try my old jets so bit of trial and error coming up
Re: Newb carb question vm34
Posted: 06:42 am Apr 06 2020
by Michael93
So my findings are you
Old carb new carb
H6-52. W8-71
V27-3. V27-3
Mj 340. Mj 320
Float bowl 1-f. Float bowl 2p
Needle 6fl52. Needle 6f39
So beside that all the dimension floats pilots seem to all be the same the 6f39 is about 4m longer and thicker at end
Re: Newb carb question vm34
Posted: 07:50 am Apr 06 2020
by Michael93
Hey thought I'd ask before I do another post so after the carb I've setteld on putting the 320 jet in which is stock I think, and put the needle on lowest clip since it longer lol, so next I check my reeds/reed block and I noticed the plastic has been melting on one side, could bad reeds cause this and be half my problem with idle/and power
Thanks
Re: Newb carb question vm34
Posted: 07:57 am Apr 06 2020
by Michael93
Michael93 wrote: ↑07:50 am Apr 06 2020
Hey thought I'd ask before I do another post so after the carb I've setteld on putting the 320 jet in which is stock I think, and put the needle on lowest clip since it longer lol, so next I check my reeds/reed block and I noticed the plastic has been melting on one side, could bad reeds cause this and be half my problem with idle/and power
Thanks
Edit sorry should mention the pedals they sit flush
Re: Newb carb question vm34
Posted: 11:57 am Apr 06 2020
by KDXGarage
I don't think the insert would be a problem.
Are you not running the stock carb?
Re: Newb carb question vm34
Posted: 07:24 pm Apr 06 2020
by Michael93
KDXGarage wrote: ↑11:57 am Apr 06 2020
I don't think the insert would be a problem.
Are you not running the stock carb?
Same carb but like I said wrong needle,
One positive is I out the 320 jet in, put needle clip lowest and I can now get a good idle so a small win,
Re: Newb carb question vm34
Posted: 07:59 pm Apr 06 2020
by KDXGarage
6FL52 is the stock OEM needle.
Re: Newb carb question vm34
Posted: 03:32 pm Apr 07 2020
by Michael93
KDXGarage wrote: ↑07:59 pm Apr 06 2020
6FL52 is the stock OEM needle.
Yep I know I bought a secondhand carby that was meant to have the needle, everything else was excately the same checked the needle and nope wrong needle :(
I guess if it's running wrong when I start it I'll just putting my finger over holes lol