Torque Specs

Questions and comments about converting to beefier forks..

Torque Specs

Postby KDX200Kev » 10:27 pm Feb 20 2006

I have 2003 KX forks and need torque settings.
- Axle Nut?
- Pinch Bolts?
- Triple Clamp Upper?
- Triple Clamp Lower 10 - 13 ft/lbs?

Thanks for helping me out in my conversion.
KDX200Kev
Member
 
Posts: 47
Joined: 12:09 am Jun 23 2005
Has thanked: 0 time
Been thanked: 0 time

Postby canyncarvr » 04:35 pm Feb 21 2006

I don't have a KX manual. That is the source you're looking for?

Don't matter a whole lot..the fastener application (where it is to be used and what type of metal) and size is going to give you a good starting point.

Axle nut? 65ft/lb
Triple upper/lower? Not over 12ft/lbs. Tops to 12 and bottoms to 10 will be fine. Ski found that anything over 10ft/lb on the bottom and initial 'stiction' troubles increase quickly.

Pinch? The '03 uses BOLT,FLANGED,8X40 in that location (that from BuyKawi).

A number 8 metric untreated bolt (what you likely have) is commonly spec'd to about 15ft/lbs. BUT...you're threading INTO aluminum. Note it's the same size fastener (threaded into aluminum) as the triple clamps.

10-12ft/lb should be just fine.

BTW, a hardness rating of 8.8 in metric-land is a medium carbon steel untreated fastener for general hardware use. Don't confuse that with an '8' Rockwell rated SAE fastener.

Generally speaking, a ft/lb wrench isn't a real good idea in the low numbers (like 10-12ft/lb). An in/lb wrench will give you better consistency.

Hope this helps! :wink:

Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis

bike profile: !clicky!
User avatar
canyncarvr
Gold Member
Gold Member
 
Posts: 6941
Images: 26
Joined: 01:07 pm Nov 05 2004
Location: The Mythical State of Jefferson
Has thanked: 0 time
Been thanked: 2 times

Postby KDX200Kev » 12:25 am Feb 22 2006

Thanks, have you had any troubles with your forks sliding within the triple clamp with that torque setting? I thought the top triple clamp would be a little tighter then the bottom, since it does not interfere with fork binding.
KDX200Kev
Member
 
Posts: 47
Joined: 12:09 am Jun 23 2005
Has thanked: 0 time
Been thanked: 0 time

Postby KDX200Kev » 11:56 pm Feb 22 2006

FYI, I just found out that the service manual for a 2003 KX states:
Front Axle: 58 ft-lbs
Front Axle Clamp Bolts: 14.5 ft-lbs
Triple Clamp Upper: 14.5 ft-lbs
Triple Clamp Lower: 14.5 ft-lbs

Too tight for the lower triple clamp but thats what it says.
Last edited by KDX200Kev on 12:01 am Aug 09 2006, edited 1 time in total.
KDX200Kev
Member
 
Posts: 47
Joined: 12:09 am Jun 23 2005
Has thanked: 0 time
Been thanked: 0 time

Postby KDXer » 06:08 am Feb 23 2006

My suspension builder also told me 14 all round. :hmm:
Image

"I want to die peacefully in my sleep like my grandfather, not screaming in terror like the passengers in his car."
User avatar
KDXer
Supporting Member
 
Posts: 2845
Joined: 12:11 pm Nov 12 2004
Location: Sydney, Downunder
Has thanked: 0 time
Been thanked: 1 time

Postby canyncarvr » 11:27 am Feb 23 2006

Yep. 14 is too tight for the bottom.

It's not a problem making the tops tigher than the bottom..not that I'm aware of anyway.

Thanks for the correct numbers!!

Facts is always good. :wink:

Consider the source
Using a perceived level of knowledge to boost my self worth.
Non impediti ratione cogitationis

bike profile: !clicky!
User avatar
canyncarvr
Gold Member
Gold Member
 
Posts: 6941
Images: 26
Joined: 01:07 pm Nov 05 2004
Location: The Mythical State of Jefferson
Has thanked: 0 time
Been thanked: 2 times

Postby skipro3 » 12:10 pm Feb 23 2006

The only time the top being tight is when you try to remove the cap for any reason. You WILL damage the cap if you don't loosen the pinch bolts first. Just and FYI for anyone not paying attention..... not that it ever happened to me of course.
Jerry

I'd rather be a smartass like carvr, than a dumbass like.... well, you fill in the blank!
User avatar
skipro3
Gold Member
Gold Member
 
Posts: 4329
Joined: 11:58 pm Nov 04 2004
Location: BANNED FOR LIFE!!
Has thanked: 0 time
Been thanked: 1 time


Return to Fork Conversion

Who is online

Users browsing this forum: No registered users and 2 guests